Larson Electronics LED UVA Fixture - 80W - Surface/Pendant Mount - Strobing - Explosion Proof
80W Explosion Proof Strobing LED UV Light Fixture - 10-100 Flashes Per Minute - 28,000mW
Made in the USA
The EPL-48-2L-IPS-UVA-STRB-RC from Larson Electronics is an Explosion Proof Strobing LED UV Light Fixture that is NRTL Listed for United States and Canada, Class I Division 1 & 2, Class II Division 1 & 2 rated, Paint Spray Booth approved, and NRTL Certified to UL 1598A Wet Locations. This fixture uses advanced LED light technology to produce ultraviolet light and is T6 rated for hazardous locations where UV lamps are used in paint and adhesive curing, food inspection or for non-destructive testing. The EPL-48-2L-IPS-UVA-STRB-RC draws a total of 80 watts and has 28,000mW of total intensity. The EPL-48-2L-IPS-UVA-STRB-RC operates on 120-277V AC voltage. The EPL-48-2L-IPS-UVA-STRB-RC has the ability to strobe at an adjustable rate of between 10 and 100 flashes per minute. The strobing rate is controlled via a hardwired remote control. The remote control must be used outside of the hazardous area.
The EPL-48-2L-IPS-UVA-STRB-RC fixture is a 2 foot long, 3 lamp, Class I Division 1 & 2 and Class II Division 1 & 2 explosion proof LED light fixture that emits light in the ultraviolet spectrum. The EPL-48-2L-IPS-UVA-STRB-RC is made to order and is typically used for curing coatings or adhesives and for non-destructive testing. This lamp is protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum coated with a high gloss reflective finish. This fixture can operate on voltages ranging from 120V-277V 50/60Hz and is approved for use in hazardous environments, paint spray booths, wet environments, and areas where UV lamps are used in paint and adhesive curing, food inspection, and for non-destructive testing.
The EPL-48-2L-IPS-UVA-STRB-RC uses LED light technology, a technology that is far better in energy saving than traditional fluorescent bulbs used for the same purposes. Traditional ultraviolet lights require a coating to block out visible light or a special composition of gases and chemicals used to create a higher concentration of ultraviolet light. This process, however, also produces many other wavelengths of light which go unused and end up as wasted energy. LED lights are unique in that they have a narrower wavelength band than traditional ultraviolet sources and therefore do not require these special coatings. As a result, LED lights do not produce unused, wasted light and therefore consume less energy than traditional UV lights on the market. LED lights have the added benefit of being capable of producing very specific wavelengths with tighter curves and are more durable and light weight as well.
LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life.
LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases, vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps.
The Class I & II, Division 1 & 2 LED ultraviolet light fixture can be used for non-destructive testing in aviation and manufacturing, food processing and inspection, and in paint, coating, and adhesive curing. The EPL-48-2L-IPS-UVA-STRB-RC provides operators in hazardous locations with a reliable and durable UV lighting solution that combines effective production of UV light with explosion proof protection and is applicable for leak detection, paint spray booths, ink, coatings, and adhesive curing, non-destructive testing, inspection, and food processing.
Strobing: The EPL-48-2L-IPS-UVA-STRB-RC is equipped with a strobe flasher and hardwired remote control for strobe rate adjustment. The EPL-48-2L-IPS-UVA-STRB-RC incorporates an onboard adjustable flash rate of 10 to 100 flashes per minute and a universal input voltage in one device and its circuitry is encapsulated. The versatility of the EPL-48-2L-IPS-UVA-STRB-RC makes it ideal for applications where various flash rates and operating voltages are required. The remote is connected to the LED UV light fixture via 20` of 16/3 SOOW chemical and abrasion resistant cord.
*PLEASE NOTE THAT THE REMOTE CONTROL MUST BE USED OUTSIDE OF THE HAZARDOUS AREA*
Mounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting configurations.
Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.
Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2" NPT junction box on one end, and a 1/2" NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires, completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.
Returns and Cancellation Notice
All Larson Electronics orders are subject to a minimum 15% cancellation fee. Larson Electronics UVC products are non-returnable once shipped. If you need help choosing a product, please contact us before ordering.
About Larson Electronics
Founded in 1973, Larson Electronic is an industrial lighting company, providing solutions for government, military, aviation, oil and gas, processing, manufacturing, and other markets. The company manufactures power distruction, industrial controls, explosion proof equipment, and UV lighting products in the USA. Larson is also able to provide customized fabrication for complex lighting and power requirements and has over 70,000 square feet of manufacturing and warehouse space.
|Country of Origin||USA|
|Dimensions||51.48" L x 11.98" W x 8.92" H|
|Lamp Type||UVA LED|
|LED Life Hours||50000|
|ProLampSales Order Code||7694762967294|
There are currently no videos for this product.
Optional Parts & Accessories
Expedited Shipping Rates
For expedited shipping, please contact us for a price quote and cutoff times.
Continental United States
- Most Orders Over $90.00 Ship Free
- Shipping for other orders is calculated at checkout
Certain restrictions apply, including oversize, heavy objects, and some fixtures/equipment.
Alaska & Hawaii
- Shipping calculated at checkout
- Contact us for a quote.
Contact us for a quote. We do not ship most glass bulbs and fixtures internationally. If you have your own UPS/Fedex/DHL account, we may be able to ship using that.
Shipping to US-Based Freight Forwarders
For shipments to freight forwarders, we are only responsible for shipping to the freight forwarder directly. Please have your freight forwarder check your items for damage. We are not responsible for shipping damages incurred after the items leave the freight forwarder.
Business Office Hours
We can be reached by phone (800-784-1998) weekdays from 7:30am to 5pm Pacific Time.
Our business office is closed Saturday and Sunday throughout the year, Memorial Day, 4th of July, Labor Day, Thanksgiving day, Christmas day and New Year's day.
Orders can be placed on the website at anytime - 24/7.
California Title 20 Notice
Certain general service lighting products are no longer allowed to be sold in California. We make every attempt to inform you before purchase which items are unable to ship to California. If we discover an item you purchased can not be shipped, we may have to cancel the order. We apologize for any inconvenience this causes. Please contact your state representative for more information.
California Prop 65
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Returns are sometimes necessary. Our policy is to provide you with a hassle-free return experience.
Items Damaged in Shipping
If the product was damaged during shipping, first keep all packing materials, then call or email us to report the damage. Damage must be reported with 3 days of you receiving the shipment. We will have you return the product using the Returned Material Authorization (RMA) we will provide. We will send you a new product or provide a full refund and we will reimburse you for any shipping charges you may incur.
If all the items you ordered are not in the shipment, call us within 3 days of receiving the shipment so we can promptly send the missing item(s).
Wrong Product Ordered or Product No Longer Needed
If you ordered the wrong product call or email us so we can help you get the correct product. If the product purchase error was in no way the fault of information provided on ProLampSales.com, you are responsible for the return shipping cost and a 25% re-stocking fee.
30 Day Return Policy
Items ordered from ProLampSales can be returned within 30 days of receipt of the shipment in most cases. Please check that all of your items are present and in working condition within this timeframe.
After 30 days, if the product does not perform to specifications or fails within stated warranty periods, see manufacturer warranty information for procedures to follow.
Products that Differ from Our General Return Policy
International orders are non-returnable.
Gas Detectors & Air Quality Monitors
For safety reasons, we do not accept returns on gas detectors or air quality monitors. Once these products leave our warehouse, we can not be sure what environments they are used/stored in or what dangerous gases or pollutants they are exposed to.
Larson Electronics UVC lighting products of any kind are non-returnable. Larson Electronics orders are subject to a minimum 15% cancellation fee. If you need help with a product, please contact us before ordering or verify that you are ordering the correct item.
Non-Quick Ship Soraa brand products are non-returnable. If an error was made in order fulfillment or shipping, replacements may be sent out or a refund issued.